Shelves that fit
Two shelves, 960 × 580: 2 mm in from each side so they slide in, 2 mm back from the front, touching the back. Tops at 1300 and 1700 from the floor.
Do it here
The model is on the left, the steps on the right. Do each step in the model: it ticks itself when it's done. Then press Check my work.
Follows the model you're drawing: each step ticks itself once it's done.
Press Set up the model. The box, back and plinth are there, locked.
You should see: The wardrobe without its shelves.
RectangleR On top of the bottom, click the inside corner at the back left, where the left side and the back meet it. Move right and towards the front, type
960,580Enter. Push/PullP Pull it up and type18Enter. SelectSpace Triple-click it, press G and name it Shelf.You should see: A shelf lying on the bottom, touching the back and the left side.
MoveM Click its front-left corner, move right, press → for the red axis and type
2Enter. Then click it again, move up, press ↑ for the blue axis and type1164Enter: its top goes from 136 to 1300.You should see: The shelf 2 in from each side, touching the back, its top 1300 from the floor.
MoveM With the shelf selected, tap Ctrl (Option on a Mac) to copy, click its corner, move up with ↑ for the blue axis and type
400Enter.You should see: A second shelf, its top at 1700.
Press Check my work.
You should see: 2 of 2 right.
Keys and axes
Tools
- RRectangle
- PPush/Pull
- MMove
- LLine
- SpaceSelect
- GMake Component (select the board first)
Axes: an arrow key locks the way you're drawing or moving
- →red axisleft and right: the width
- ←green axisfront and back: the depth
- ↑blue axisup and down: the height
- ShiftAlready moving along an axis? Hold Shift and it stays on it.
- CtrlWith Move: makes a copy (Option on a Mac)
- EscCancels what you're doing
Sizes: just type, they go in the Measurements box at the bottom right, then Enter. Two sizes: 1000,600 (1000;600 if your computer writes decimals with a comma).
On a tablet or phone: press Full screen, tap to click, drag one finger to move the pointer while you draw (or to turn the view), pinch with two fingers to zoom, and type sizes on the keypad under the model (its red, green and blue keys lock an axis, as the arrow keys do). A mouse and keyboard is quicker.
Where it goes
The boards
Every size in millimetres, worked out from the wardrobe's 1000 × 2100 × 600.
Lower shelf
960 × 580 × 18964 inside − 2 − 2 = 960 wide; 600 − 18 back − 2 at the front = 580 deep.
2 in from each side, 2 back from the front, touching the back, its top 1300 from the floor.
Upper shelf
960 × 580 × 18The same as the lower shelf: 960 × 580.
Right above the lower one, its top 1700 from the floor (400 higher).
Stuck?Show a hint
Inside the box is 1000 − 18 − 18 = 964, and the shelf is 2 shorter at each end so it slides in: 960. It's 600 − 18 back − 2 at the front = 580 deep. Drawn on the bottom its top is at 100 + 18 + 18 = 136, so it goes up 1300 − 136 = 1164.
What Check my work looks at
- Every board's size, to 1 mm
- Where each board is, to 1 mm
- Which way each board is turned
- That each board is its own component
- That nothing is left loose